International Interprotect Two-Component Epoxy Primer for Superior Corrosion Protection

Description

International Interprotect is a high performance two pack primer/undercoat. Easy to apply and quick drying, 

• An epoxy polyamide primer that can be recoated with itself for up to 6 months
• Easy to sand and quick to dry
• Good abrasion resistance
• Offers excellent anticorrosive protection
• Can be used as an antifouling tie-coat over existing epoxy primers
• Below the Water: First Coat thinned 10-15% with Thinner No.7, then 4-5 coats

Use in these areas

Suitable for above  and below waterline

• Hull
• Keel
• Bilge/Lockers
• Exterior cabin/trims
• Interior cabin/trims
• Propeller
• Drive

Use for substrates

• Aluminium / Zinc-Galvanised Steel
• Epoxy Composite / Carbon Fibre
• GRP / FRP
• Lead
• Steel
• Wood

 Pack Size

750ml

Preparation

Steel: Degrease with solvent or Super Cleaner. Grit-blast to Sa 2½ – near white metal surface. If grit-blasting is not possible, grind the metal surface with 24-36 grit abrasive discs to a uniform, clean, bright metal surface with a 50¬75 microns anchor pattern. Use angle grinder on small areas.

Aluminium: Degrease with solvent or Super Cleaner. Sand well using 24- 120 grade (aluminium compatible) paper. Coarser grades are recommended to achieve optimum adhesion. Clean thoroughly and allow to dry. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

Zinc/Galvanised Steel: Degrease with solvent or Super Cleaner. Sand well using 60-120 grade paper. Clean thoroughly and allow to dry completely. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

Stainless Steel: Light grit blast to produce a profile of 50 microns. Clean thoroughly and allow to dry completely. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

Lead: Degrease with solvent or Super Cleaner. Sand well using 120 grade paper or power wire brush clean thoroughly and allow to dry. Prime using a recommended International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

Bare Wood: Sand smooth with 80-180 and then 280 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying products recommended for application direct to wood (see specific coating systems).

Hazard Warnings

Hazard Pictogram :
Signal Word:	Warning
Hazard Statements:	Flammable liquid and vapour Causes skin irritation Causes serious eye damage May cause an allergic skin reaction Harmful to aquatic life with long lasting effects
Precautionary Statement:	General: Keep out of reach of children. Prevention: P210 – Keep away from heat / sparks / open flames / hot surfaces – No smoking P260 – Do not breathe mist / vapours / spray P261 – Avoid breathing dust / fume / gas / mist / vapours / spray P264 – Wash thoroughly after handling P272 – Contaminated work clothing should not be allowed out of the workplace P273 – Avoid release to the environment P280 – Wear protective gloves / eye protection / face protection Response: P301+310 IF SWALLOWED – Immediately call a POISON CENTER or doctor / physician P302+352 IF ON SKIN – Wash with soap and water P303+361+353 IF ON SKIN (or hair) – Remove / Take off immediately all contaminated clothing Rinse skin with water / shower P305+351+338 IF IN EYES – Rinse continuously with water for several minutes Remove contact lenses if present and easy to do – continue rinsing P310 – Immediately call a POISON CENTER or doctor / physician P321 – Specific treatment (see information on this label) P331 – Do NOT induce vomiting P333+313 – If skin irritation or a rash occurs: Get medical advice / attention P362 – Take off contaminated clothing and wash before reuse P363 – Wash contaminated clothing before reuse P370 – In case of fire P378 – Use alcohol resistant foam, CO2, powder, water spray for extinction. Do not use water jet Storage: P403+233 – Store in a well ventilated place. Keep container tightly closed. Disposal: P501 – Dispose of contents / container in accordance with local / national regulations.
Hazardous Ingredients	Epoxy Resin, N-Butanol, Xylene, Ethyl Benzene, Solvent Naphtha (petroleum), Light Aromatic, Amorphous Silica Gel, Aluminium Hydroxide.

Interprotect Part A White Safety Data Sheet

Interprotect Part B White Safety Data Sheet

Interprotect Part A Grey Safety Data Sheet

Interprotect Part B Grey Safety Data Sheet

Explore more from our collection.